Fault codes › Yaskawa Solectria

Yaskawa Solectria fault codes

Solectria PVI 14/20TL

Code	Shown as	Class	Production	Clears	Reports	Page
Arc Board Error	Internal Arc board self-check error	warning		by itself	Self-test failure	48
Arc Protect		fault	stops	by itself	Arc fault detected	51
EepromErr	Incorrect memory reading	warning		by itself	Internal memory error	48
ExtFanErr		warning		by itself	Fan fault alarm	48
GFCI.Err	DC leakage current is above recommend value	fault		by itself	High leakage current	51
GridF.OutLim		fault		by itself	Grid frequency out of range	50
GridV.OutLim	Grid voltage exceeds the specified range	fault		by itself	Grid voltage out of range	49
IntFanErr		warning		by itself	Fan fault alarm	47
IntFaultA~O	Internal noncritical fault within the inverter	fault		by itself	Internal device fault	51
IntProtectA~Z	Internal problem within the inverter	fault	stops	by itself	Internal device fault	51
OverTemp		fault		by itself	Inverter overtemperature	49
PV1 (2) Reverse	DC inputs connected with incorrect polarities	fault			Reverse polarity	50
PV1 (2) VoltOver	DC input voltage exceeds the specified value	fault		by itself	DC overvoltage	50
SPICommErr	Inverters internal communication failure	warning		by itself	Internal communication failure	47
TempSensorErr	Abnormal temperature reading	warning		after a manual reset	Abnormal temperature reading	47

Solectria PVI 20/25TL-480-R

Code	Shown as	Class	Production	Clears	Reports	Page
Arc Protect			stops	by itself	Arc fault detected	82
CommErr		warning		by itself	Internal communication failure	78
GFCI.Err	leakage current high			by itself	High leakage current	81
GridF.OutLim				by itself	Grid frequency out of range	80
GridV.OutLim				by itself	Grid voltage out of range	80
IntFanErr				by itself	Fan fault alarm	79
IsolationErr	Insulation resistance low				Low insulation resistance	81
PV Reverse	PV input reverse connection				Reverse polarity	82
PVVoltOver					DC overvoltage	82
TempOver	Over-temperature protection	fault		by itself	Inverter overtemperature	80
Fault0020	Bus over volt Hardware	fault		after a manual reset	DC bus overvoltage	84
Fault0060	CPLD Fault	fault		after a manual reset		84
Fault0090	Static leakage current high	fault			High leakage current	83
Fault0100	Grid relay fault	fault		after a manual reset		83
Fault0110	Bus imbalance	fault			Neutral point voltage imbalance	83
Fault0130	Bus over total voltage	fault		after a manual reset	DC bus overvoltage	83
Fault0150	Open-loop self-check failure	fault		after a manual reset	Self-test failure	84
Protect0020	Grid relay error	fault		after a manual reset		80
Protect0030	Inverter Over Current	fault		after a manual reset	Inverter overcurrent	80
Protect0070	Bus imbalance	fault			Neutral point voltage imbalance	80
Protect0100	The sensor fault of leakage current	fault		after a manual reset		82
Protect0110	BUS over voltage (firmware)	fault		after a manual reset	DC bus overvoltage	82
Protect0150	Mini MCU Fault	fault		after a manual reset	Internal device fault	81
Protect0170	DCI high	fault			High DC injection	81
Protect0180	The sampling offset of DCI	fault			DC injection monitoring error	81
Protect0230	Inverter open-loop self-test fault	fault		after a manual reset	Self-test failure	82
WARN-30	EepromErr	warning	stops		Unauthorized network access attempt	79
Warn0040	DC SPD fault	warning			Surge protector alarm	79
Warn0050	TempSensorErr	warning		after a manual reset	Abnormal temperature reading	79
Warn0100	AC SPD fault	warning			Surge protector alarm	79

Solectria PVI 23/28/36TL

Code	Shown as	Class	Production	Clears	Reports	Page
Arc Board Error	Internal Arc board self-check error	fault		by itself	Self-test failure	53
Arc Protect		fault	stops	by itself	Arc fault detected	55
EepromErr	Incorrect memory reading	warning		by itself	Internal memory error	53
ExtFanErr		warning		by itself	Fan fault alarm	52
GFCI.Err	DC leakage current is above recommended value	fault		by itself	High leakage current	54
GridF.OutLim	Grid voltage frequency is abnormal	fault		by itself	Grid frequency out of range	54
GridV.OutLim	Grid voltage exceeds the specified range	fault		by itself	Grid voltage out of range	53
IntFanErr		warning		by itself	Fan fault alarm	52
IsolationErr	DC insulation impedance to ground	fault		needs service	Low insulation resistance	54
OverTemp		fault		by itself	Inverter overtemperature	53
PV1 (2) Reverse	DC inputs connected with incorrect polarities	fault			Reverse polarity	54
PV1 (2) VoltOver	DC input voltage exceeds the specified value	fault		by itself	DC overvoltage	54
SPICommErr	Inverter's internal communication failure	warning		by itself	Internal communication failure	52
TempSensorErr	Abnormal temperature reading	warning		after a manual reset	Abnormal temperature reading	52
IntFault0010-150	Internal non-critical fault within the inverter	fault	stops	by itself	Internal device fault	55
IntProtect0010-0260	Internal problem within the inverter	fault	stops	by itself	Internal device fault	55

Solectria SGI 500/750XTM

Code	Class	Production	Clears	Reports	Page
AC Islanding	informational	stops		Grid loss	115
Contactor Fail	fault	stops	after a manual reset	Switching device status fault	114
CT Failure	fault		after a manual reset		114
Current Limit	informational	reduced		Inverter power derating	115
DC Cont. Err	informational		needs service	Contactor fails to open	115
DC GND Fault	fault		needs service	Ground fault alarm or trip	114
DC Overshoot	informational		after a manual reset	DC bus overvoltage	115
DC Volt High	informational			DC overvoltage	115
DC Volt Low	informational	stops	by itself	Insufficient DC input power	115
Desat Error	fault		after a manual reset	Internal device fault	114
Fac High	informational	stops	by itself	Grid overfrequency	115
Fac Low	informational	stops	by itself	Grid underfrequency	115
Fac Very Low	informational	stops	by itself	Grid underfrequency	115
Fan Life Reached	informational		needs service	Fan service life reached	115
Filter Cont. Err	warning	unaffected	after a manual reset	Output filter malfunction	115
Flux Error			after a manual reset	Grid synchronization failure	115
Hw Interlock		stops	after a manual reset	DC undervoltage	115
IGBT Overtemp	fault		after a manual reset	Inverter overtemperature	114
Low DC Power	informational	stops	by itself	Insufficient DC input power	115
Master NTC Error			needs service		115
MOV Fault	warning	unaffected	needs service		114
MPP Tracking	informational	unaffected			115
Nameplate Limits	informational	reduced		Flat capped output	116
NTC Failure	fault		after a manual reset		114
Open Phase	fault			Phase loss	114
Other PB Fault			needs service		116
Outside MPPT	informational				116
PAR Backup Err			needs service	Configuration error	116
PAR Config Err			needs service	Configuration error	116
Power Derated	warning	reduced	needs service	Inverter power derating	116
Power Disabled	informational	stops		Remote shutdown	116
PS Fail			needs service		116
PS Wake Fail		stops	after a manual reset		116
Pw Brd Mismatch			needs service	Configuration error	116
PWM Trip			after a manual reset		116
RCM Fault	fault		needs service	Ground fault alarm or trip	114
RCM Warn	warning	unaffected		High leakage current	116
Remote Limiting	informational	reduced		Remote power limit	116
Reverse Phase		stops	after a manual reset	Incorrect phase sequence	116
Shunt Trip	fault	stops	after a manual reset	Remote shutdown	114
Slave NTC Error			needs service		116
Slave Trip			needs service		116
Soft Shutdown		stops	after a manual reset	Remote shutdown	116
Temp 1 Limiting		reduced		Inverter overtemperature	116
Temp 2 Limiting		reduced		Inverter overtemperature	116
Temp 3 Limiting		reduced		Inverter overtemperature	116
Vac High		stops	by itself	Grid overvoltage	117
Vac Low		stops	by itself	Grid undervoltage	117
Vac Very High		stops	by itself	Grid overvoltage	117
Vac Very Low		stops	by itself	Grid undervoltage	117
Vsense Error	fault		needs service		114
Vsense Mismatch				Software version mismatch	117
Wait for Grid		stops		Grid loss	117
Wait to Restart	informational	stops	by itself		117
Temp 4		reduced			116

Yaskawa Solectria XGI 1500

Code	Shown as	Class	Production	Clears	Reports	Page
CRIT-1	Software Parameter Load Failure	fault		after a manual reset	Parameter download failure	52
CRIT-2	Internal Communication 1 Failure	fault		after a manual reset	Internal communication failure	52
CRIT-3	Internal Communication 2 Failure	fault		after a manual reset	Internal communication failure	52
CRIT-4	ARC Fault Detected	fault		after a manual reset	Arc fault detected	52
CRIT-5	AC Contactor Failure	fault		after a manual reset	Switching device status fault	52
CRIT-6	Critical Over Temperature	fault			Inverter overtemperature	53
CRIT-7	Ground Fault, Excessive Leakage Current	fault		needs service	Ground fault alarm or trip	53
CRIT-8	Ground Fault, Isolation Resistance Low	fault				53
CRIT-9	Critical Internal Hardware Failure	fault		after a manual reset	Internal device fault	53
CRIT-10	Ground Fault Detection Self Check Failure	fault				53
CRIT-11	Operational Self Check Failure	fault		after a manual reset	Self-test failure	53
CRIT-12	Startup Self Check Failure	fault		after a manual reset	Self-test failure	53
CRIT-32		fault				53
INFO-1	Power Derating, Temperature	informational	reduced		Inverter overtemperature	56
INFO-2	Power Derating, Customer Command	informational	reduced		Remote power limit	56
INFO-32		informational				56
WARN-1	Internal Over Current/ Over Voltage	warning	stops	after a manual reset	Internal overcurrent or overvoltage	54
WARN-2	Phase Lock Loop Failure	warning	stops	after a manual reset	Grid synchronization failure	54
WARN-3	Islanding Detected	warning	stops	by itself	Islanding detected	54
WARN-4	Open Phase Detected	warning	stops	by itself	Phase loss	54
WARN-5	AC Low Frequency 1 Detected	warning	stops	by itself	Grid underfrequency	54
WARN-6	AC Very Low Frequency 2 Detected	warning	stops	by itself	Grid underfrequency	54
WARN-7	AC High Frequency 1 Detected	warning	stops	by itself	Grid overfrequency	54
WARN-8	AC Very High Frequency 2 Detected	warning	stops	by itself	Grid overfrequency	55
WARN-9	AC Low Voltage 1 Detected	warning	stops	by itself	Grid undervoltage	55
WARN-10	AC Very Low Voltage 2 Detected	warning	stops	by itself	Grid undervoltage	55
WARN-11	AC Extremely Low Voltage 3 Detected	warning	stops	by itself	Grid undervoltage	55
WARN-12	AC High Voltage 1 Detected	warning	stops	by itself	Grid overvoltage	55
WARN-13	AC Very High Voltage 2 Detected	warning	stops	by itself	Grid overvoltage	55
WARN-25	Communication 1 Fault	warning	stops	after a manual reset	Internal device fault	55
WARN-26	Communication 2 Fault	warning	stops	after a manual reset	Internal device fault	55
WARN-27	Communication 3 Fault	warning	stops	after a manual reset	Internal device fault	56
WARN-28	Network Fault	warning	stops		Communication loss	56
WARN-29	Software Update Fault	warning	stops	after a manual reset	Firmware update failure	56
WARN-30	Unauthorized Network Access	warning	stops		Unauthorized network access attempt	56
WARN-31	Invalid Configuration Request	warning	stops		Parameter change rejected, Configuration error	56
WARN-32		warning				56

Yaskawa Solectria XGI 1500-1MW

Code	Shown as	Class	Production	Clears	Reports	Page
CRIT-1	Software Parameter Load Failure	fault		after a manual reset	Parameter download failure	64
CRIT-2	Internal Communication 1 Failure	fault		after a manual reset	Internal communication failure	64
CRIT-3	Internal Communication 2 Failure	fault		after a manual reset	Internal communication failure	64
CRIT-5	AC Contactor Failure	fault		after a manual reset	Switching device status fault	64
CRIT-6	Critical Over Temperature	fault			Inverter overtemperature	64
CRIT-7	Ground Fault	fault		needs service	Ground fault alarm or trip	64
CRIT-9	Critical Internal Hardware Failure	fault		after a manual reset	Internal device fault	64
CRIT-11	Operational Self Check Failure	fault		after a manual reset	Self-test failure	64
CRIT-12	Startup Self Check Failure	fault		after a manual reset	Self-test failure	64
CRIT-32		fault				64
INFO-1	Power Derating, Temperature	informational	reduced		Inverter overtemperature	67
INFO-2	Power Derating, Customer Command	informational	reduced		Remote power limit	67
WARN-1	Internal Over Current/ Over Voltage	warning	stops	after a manual reset	Internal overcurrent or overvoltage	65
WARN-2	Phase Lock Loop Failure	warning	stops	after a manual reset	Grid synchronization failure	65
WARN-3	Islanding Detected	warning	stops	by itself	Islanding detected	65
WARN-4	Open Phase Detected	warning	stops	by itself	Phase loss	65
WARN-5	AC Low Frequency 1 Detected	warning	stops	by itself	Grid underfrequency	65
WARN-6	AC Very Low Frequency 2 Detected	warning	stops	by itself	Grid underfrequency	65
WARN-7	AC High Frequency 1 Detected	warning	stops	by itself	Grid overfrequency	65
WARN-8	AC Very High Frequency 2 Detected	warning	stops	by itself	Grid overfrequency	66
WARN-9	AC Low Voltage 1 Detected	warning	stops	by itself	Grid undervoltage	66
WARN-10	AC Very Low Voltage 2 Detected	warning	stops	by itself	Grid undervoltage	66
WARN-11	AC Extremely Low Voltage 3 Detected	warning	stops	by itself	Grid undervoltage	66
WARN-12	AC High Voltage 1 Detected	warning	stops	by itself	Grid overvoltage	66
WARN-13	AC Very High Voltage 2 Detected	warning	stops	by itself	Grid overvoltage	66
WARN-25	Communication 1 Fault	warning	stops	after a manual reset	Internal device fault	66
WARN-26	Communication 2 Fault	warning	stops	after a manual reset	Internal device fault	66
WARN-27	Communication 3 Fault	warning	stops	after a manual reset	Internal device fault	67
WARN-28	Network Fault	warning	stops		Communication loss	67
WARN-29	Software Update Fault	warning	stops	after a manual reset	Firmware update failure	67
WARN-30	Unauthorized Network Access	warning	stops		Unauthorized network access attempt	67
WARN-31	Invalid Configuration Request	warning	stops		Parameter change rejected	67
WARN-32		warning				67

Yaskawa Solectria XGI 1500-DCG

Code	Shown as	Class	Production	Clears	Reports	Page
CRIT-1	Software Parameter Load Failure	fault		after a manual reset	Parameter download failure	54
CRIT-2	Internal Communication 1 Failure	fault		after a manual reset	Internal communication failure	54
CRIT-3	Internal Communication 2 Failure	fault		after a manual reset	Internal communication failure	54
CRIT-5	AC Contactor Failure	fault		after a manual reset	Switching device status fault	54
CRIT-6	Critical Over Temperature	fault			Inverter overtemperature	54
CRIT-7	Ground Fault	fault		needs service	Ground fault alarm or trip	55
CRIT-9	Critical Internal Hardware Failure	fault		after a manual reset	Internal device fault	55
CRIT-11	Operational Self Check Failure	fault		after a manual reset	Self-test failure	55
CRIT-12	Startup Self Check Failure	fault		after a manual reset	Self-test failure	55
CRIT-32	Reserved	fault				55
INFO-1	Power Derating, Temperature	informational	reduced		Inverter overtemperature	58
INFO-2	Power Derating, Customer Command	informational	reduced		Remote power limit	58
WARN-1	Internal Over Current/ Over Voltage	warning	stops	after a manual reset	Internal overcurrent or overvoltage	56
WARN-2	Phase Lock Loop Failure	warning	stops	after a manual reset	Grid synchronization failure	56
WARN-3	Islanding Detected	warning	stops	by itself	Islanding detected	56
WARN-4	Open Phase Detected	warning	stops	by itself	Phase loss	56
WARN-5	AC Low Frequency 1 Detected	warning	stops	by itself	Grid underfrequency	56
WARN-6	AC Very Low Frequency 2 Detected	warning	stops	by itself	Grid underfrequency	56
WARN-7	AC High Frequency 1 Detected	warning	stops	by itself	Grid overfrequency	56
WARN-8	AC Very High Frequency 2 Detected	warning	stops	by itself	Grid overfrequency	57
WARN-9	AC Low Voltage 1 Detected	warning	stops	by itself	Grid undervoltage	57
WARN-10	AC Very Low Voltage 2 Detected	warning	stops	by itself	Grid undervoltage	57
WARN-11	AC Extremely Low Voltage 3 Detected	warning	stops	by itself	Grid undervoltage	57
WARN-12	AC High Voltage 1 Detected	warning	stops	by itself	Grid overvoltage	57
WARN-13	AC Very High Voltage 2 Detected	warning	stops	by itself	Grid overvoltage	57
WARN-25	Communication 1 Fault	warning	stops	after a manual reset	Internal device fault	57
WARN-26	Communication 2 Fault	warning	stops	after a manual reset	Internal device fault	57
WARN-27	Communication 3 Fault	warning	stops	after a manual reset	Internal device fault	58
WARN-28	Network Fault	warning	stops		Communication loss	58
WARN-29	Software Update Fault	warning	stops	after a manual reset	Firmware update failure	58
WARN-30	Unauthorized Network Access	warning	stops		Unauthorized network access attempt	58
WARN-31	Invalid Configuration Request	warning	stops		Parameter change rejected	58
WARN-32		warning				58

Codes are sorted by vendor prefix and number. Each row links to the code's record; concepts link to their reading rule.